Push-On-Lock High-Frequency Coaxial Connectors

  SMP Connectors
• The push-on-lock coaxial connector supports an optical communications system or a
high-capacity and high-speed transmission system, which is required for use with
high-density system and high-frequency band.
• Provides a hermetic type receptacle, which supports applications required for airtightness.
• Conforms to MIL-STD-348A.
• Lineup of products
Jacks: Straight type, right-angle type and relay adapter.
Receptacles: Hermetic type, board-edge mounting type, SMT type and panel mounting type
Conversion adapters: K connector to SMP connector

Specifications    
Characteristic impedance : 50 ohms
Frequency range DC to 40.0 GHz (straight type)
DC to 26.5 GHz (right-angle type)
Rated voltage : 335 V (r.m.s.)
VSWR : 1.5 or less, at DC to 40 GHz frequency range (straight type)
Insulation resistance : Over 5,000 megohms, at 500 V (r.m.s.)
Dielectric withstanding voltage : 500V AC
Contact resistance : Center contact: 6 milliohms or less
Outer contacts: 2 milliohms or less

  Coaxial Antenna
  For Antenna
• 2.4 GHz bow-tie antenna: For wireless LAN access point (for fixed station).
Colinear antenna
• Two 2.4 GHz elements or three 2.4 GHz elements (SMA connector): These antennas are installed in the panoptic location, and communications are performed by radio.
  Flat antenna
• 2.4 GHz patch antenna: For wireless LAN access point (for fixed stations)
• 5.2 GHz or 2.4/5.2 GHz patch antenna: These antennas are installed in the location such as superiority of unidirectional or bidirectional communications and communications are performed by radio.
  Inverted-F antenna
• 2.4 GHz antenna: This antenna is built into the chassis. (For movable stations)
• 2.4/5.2 GHz flexible antenna: This antenna is mainly built into note PCs and communications are performed by radio.

 
 
  FLX Series
• Snap-on-type ultra miniature connectors compatible with "MMCX connectors" used in Europe and America.
• Available in three types of plug connectors for cables and PCBs. Cables for use with these connectors are RG-188A/U, RG-178B/U and 1.5D-2V. These plug connectors are available pre-assembled with the cables and supplied by HONDA.
• Provides jack connectors only for mounting on PCBs, and available in three types, SMT, slide mount, and PCB DIP. Also, this series provides male and female convertible adaptors with SMA male and female screws on the opposite end.
• Electrical characteristics, VSWR is 1.2 or less up to 6GHz.

Specifications    
Characteristic impedance : 50 ohms
Dielectric withstanding voltage : 500 V AC (r.m.s.) for up to one minute
Insulation resistance : Over 500 megohms
Contact resistance : 10 milliohms or less
VSWR : 1.2 or less up to 6GHz

 
 
  FG-Y Series
• These are smaller-sized light-weight coaxial connectors we developed on the basis of SMB type connectors complying with MIL standards, and also the C05 type connectors complying with JIS standards. These connectors are designed to withstand mechanical vibrations.
• Structured so that the external electric conductor, with its slit projections, is firmly fastened by an annular spring in an inward direction, and the conductor is supported at three points in the axial direction, thereby assuring stable contact.
• Applications: Smaller-sized wireless telephones, cellular phones, etc. Suitable for coaxial cables used for high-speed digital transmission to and from computers.

Specifications    
Dielectric withstanding voltage : 500 V AC (r.m.s.) for up to one minute
Insulation resistance : Over 500 megohms
Contact resistance : 6 milliohms or less
VSWR : 1.2 or less up to 2GHz

 
 

  FLA Series
• Smaller-sized coaxial connectors compatible with the SMA type connectors (MIL-C-39012, IEC-169-15) which are standard connectors for the microwave band.
• Since the discontinuous capacitance of connectors is compensated for by the unique technology, these connectors can be used for frequencies up to the microwave band.
• Some connectors can be used up to 26.5 GHz.

Specifications    
Characteristic impedance : 50 ohms
Dielectric withstanding voltage : 1,000 V AC (r.m.s.) for up to one minute
Contact resistance : Less than 4 milliohms (center and external contact)
Durability : 6 milliohms or less after 1,000 cycles of insertion and extraction
VSWR : 1.05 + 0.01 f (f = Frequency in GHz)

 
 

K Connectors (2.92 mm)

  FLK Series
• Suitable for input or output terminal of high-frequency instruments, etc.
• Supports a wide range of frequencies such as DC to 40GHz.
• Capable of mating with an SMA male or female coaxial connector

Specifications    
Rated voltage : 500 V
Dielectric withstanding voltage : 1,000 V AC (r.m.s.) for up to one minute
Insulation resistance : Over 5,000 megohms at 500 V DC
Characteristic impedance : 50 ohms
Operating frequency : DC to 40 GHz

 
 

S-SMA Type Coaxial Connectors

  FLAM Series
• Suitable for wiring in equipment required high-density mounting
• Provides smaller-sized connectors than SMA type coaxial connectors while the characteristic impedance is equivalent to that of SMA type coaxial connectors.

Specifications    
Rated voltage : 500 V
Dielectric withstanding voltage : 1,000 V AC (r.m.s.) for up to one minute
Insulation resistance : Over 5,000 megohms at 500 V DC
Characteristic impedance : 50 ohms
Operating frequency : DC to 26.5 GHz

 
 

MU Type High-Density Plug-in Coaxial Connector

  FXMU Series
• The MU type coaxial connector inherits from our design of conventional MU type fiber optic connectors. Additionally, the existing MU type housing is used, making high-density mounting possible.
• Plug, adaptor or plug-in type housing (for backplane or package) is utilized, making the mounting method the same as the mounting method of MU type fiber optic connectors.
• The MU type coaxial connector uses the same push-pull mechanism as conventional MU type fiber optic connectors.
• By replacing the MU type fiber optic connector with the MU type coaxial connector, which consists of plug and jack, the housing for MU type fiber optic connectors can be used.
• Capable of using an MU type fiber optic connector and coaxial connector as a complex connector.

Specifications    
Characteristic impedance : 50 and 75 ohms
Dielectric withstanding voltage : 500 V AC (r.m.s.) for up to one minute
Insulation resistance : Over 500 megohms
Contact resistance : 10 milliohms or less (50 ohms)
15 milliohms or less (75 ohms)
VSWR : 1.25 or less up to 3 GHz

 
 

Adapter Type Coaxial Connectors Built into Lightning Arrester

  FRS Series
• Designed to protect the main body of equipment against induced lightning high-voltage current through wires such as antenna wires, electric power distribution lines, transmission lines and similar power lines.
• The connector is structured such that when lightning more current flows than the rating of the equipment; a built-in gas-tube arrester discharges the electric current and passes it to ground. Consequently, the connector minimizes damage to the equipment from lighting current.
• HONDA TSUSHIN provides two types, N type and F type coaxial connectors. However, we can manufacture other type coaxial connectors depending on frequency characteristics, so please contact us.
• Principal applications: Cable television, Wireless LAN systems, Antenna equipment for cellular phones and PHS base stations, etc.

Specifications    
Fequency range : DC to 1GHz [F type]
DC to 3 - 6GHz [N type]
Characteristic impedance : 75 ohms [F type]
50 ohms [N type]
Impulse wave current immunity : 8/20 sec 2.5kA (one time) [F type]
15/100 sec 1kA (one time) [N2]
8/20 sec 10kA (one time) [N3]
8/20 sec 5kA (one time) [N4]

 
 

Back Type Coaxial Connectors

  FN/FFA/FLA Series
• These connectors are convertible adapters, FN series N type, FFA series TNC type, and FLA series SMA type, connectors available to interface to an antenna in order to measure the signals from the antenna. An antenna can be directly connected with the connector in order to measure the signals because the back type coaxial connector is mounted on the back of PCB. Therefore, the antenna can be effectively evaluated.